钢跳板成型设备（现货）

钢跳板成型设备简介 技术标准 1.1 GB/T6725-2002 《冷弯型钢技术条件》 1.2 GB/T6728-2002 《结构用冷弯空心型钢尺寸、外型、重量及允许偏差》 1.3 GB6723-86 《通用冷弯开口型钢尺寸、外形、重量及允许偏差》 1.4 GB/709-88 《热轧钢板和钢带的尺寸、外形、重量及允许偏差》 1.5 GB/708-88 《冷轧钢板和钢带的尺寸、外形、重量及允许偏差》 2.设备技术要求 2.1设备技术条件： 2.1.1设备占地面积：45×3.0×5（长×宽×高）米。（根据最后提供地基图为准） 2.1.2设备进料方向：左进料。 2.1.3电压参数380，50Hz，3相。 2.1.4气源：流量为0.5m3/分钟；压力为0.6MPa。 2.1.5液压油：46#液压油。 2.1.6齿轮油：18#双曲线齿轮油。 2.2设备主要技术参数 2.2.1 轧制带钢宽度：≤500 mm 2.2.2 轧制带钢厚度：2 mm 2.2.3 轧制带钢材质：GI 带钢 2.2.4生产速度:全线冲孔速度约为8米/分钟以上 2.2.4 轧制工件长度：2000.6000 mm 2.2.5设备装机总容量：44.9 KW。 3.轧制产品范围 3.1 本冲压/成型机组可以轧制厚度为2mm 的脚踏板型材。 3.2 轧制产品规格尺寸 （最终以客户提供型材图为准） 4.供货及服务范围 4.1本条款规定了合同设备的供货范围（见表二），卖方保证所提供设备为全新的、成熟的、完整的和安全可靠的，且设备的技术性能、功能符合技术条件的要求。 钢跳板成型设备 Foot pedal device profile The technical standards 1.1 GB/T6725-2002 "the cold bending steel technical conditions" 1.2 GB/T6728-2002 "structure with cold bending hollow section size, shape, weight.allowable deviation" 1.3 GB6723-86 "general opening cold bend steel size, shape, weight.allowable deviation" 1.4 GB / 709-709 "hot rolled steel plate.steel belt of the size, shape, weight.allowable deviation" 1.5 GB / 708-708 "cold rolled steel plate.steel belt of size, shape, weight.allowable deviation" 2. The equipment technical requirements 2.1 equipment technical conditions: 2.1.1 equipment area: 45 * 3.0 * 5 meters (length x width x height). (according to finally provide foundation drawing shall prevail) 2.1.2 device feed direction: left feed. 2.1.3 voltage parameters for 380, 50 Hz, 3 phase. 2.1.4 gas source: flow of 0.5 m3 / min; Pressure is 0.6 MPa. 2.1.5 hydraulic oil: 46 # hydraulic oil. 2.1.6 gear oil: 18 # hyperbolic gear oil. 2.2 equipment main technical parameters 2.2.1 rolling strip width: 500 mm.less 2.2.2 rolling strip steel thickness: 2 mm 2.2.3 rolling steel strip material: GI strip steel 2.2.4 production speed: all punching speed is about more than 8 m/min 2.2.4 rolling workpiece length: 2000-6000 mm 2.2.5 equipment installed gross capacity: 44.9 KW. 3. Rolling product range 3.1 the stamping/molding unit can pedal profile rolling thickness of 2 mm. 3.2 size rolled products (final customer provide profile figure shall prevail) 4. The scope of supply.services The provisions of this clause 4.1 of the contract equipment scope of supply (see chart 2), the seller guarantees that the equipment for new, mature, complete,.safe.reliable,.the equipment of the technical performance.function accord with the requirement of technical conditions.